Identification bar light for over-80” wide applications.
Corrosion
resistant bar is 24-gauge steel with black enamel finish and three #136 oval
lights attached. Mounts on 6 15/16” centers,
includes single lead wire, and
grounds
through mounting hardware. Available in amber or red.
Thin-line, surface-mount lamp features high-impact base
with scratch resistant acrylic lens. May be mounted horizontally or
vertically. Includes single lead wire and grounds through mounting screw.
Available in amber
or
red.
Stud-mount
light functions as side marker or clearance light with reflex. Grounds
through mounting stud. Unit has single wire for electrical connection.
Features 15,000-hour long-life bulb. Available in amber or red.
Dual function red/amber clearance/side marker light fender mount. Lexan lens, 3-11/16"x1-5/16"x1-1/16" w/ 1/2" depth.
SEALED
Lights available in amber or red and functions as side marker or clearance
light. May be used as combination side marker and clearance light when
properly mounted. Lens is welded to housing to form single unit. Requires
mounting grommet and 2-wire plug to complete installation. Features
15,000-hour long-life bulb.
With standard lens:
With reflective lens:
Oval,
10-diode LED stop, turn, and tail light. Features sealed lens
and housing, and operates from 8-32 volts. Regulated design provides voltage
protection and consistent light output over entire voltage range. Meets
FMVSS
108 and ECE requirements in horizontal, vertical, or any 360o position.
Combination
tail light. Includes the following functions: stop, turn, tail, rear
clearance, rear reflex, side marker, side reflex, and license light (“L”
suffix only). Features push-in connections with two extra ports for
additional lights. Mounts on 2” centers and includes mounting hardware.
Grounds
through
mounting studs.
Available in
amber or red and functions as side marker or clearance light. May be used as
combination clearance and side marker light when properly mounted. Lens is
welded to housing to form single unit. Mounting bracket and electrical
connector are included. Features two 15,000-hour
long-life
bulbs.
Available
in amber or red and functions as side marker or clearance light. May be used
as combination clearance and side marker light when properly mounted. Lens
is welded to housing to form single unit. 150 series has female terminals
and features 15,000-hour long-life bulb. Rubber
grommet
and electrical plug included.
Sealed, oval
stop, turn, and tail light may be used on both curbside and roadside of
vehicle or trailer. Legal in either horizontal or vertical position.
Polycarbonate lens is welded to housing to form single unit. Includes
mounting
grommet and 3-wire plug to complete installation.
Sealed surface
mount license light. Polycarbonate lens and
housing
are sonic welded for watertight seal. Mounts on 2
3/4” centers. Electrical plug included.
Features
our patented VIBAR® socket, tough polycarbonate lens, and ABS hood. All
internal parts are durable stainless steel or tinned-brass. Surface mounts
on 3 1/4” centers. 436B includes a black powder-coated,
steel
license plate bracket riveted to light.
License
Plate Holder with Integral Light
A permanent light fixture using a high output light-emitting diode as the
lamp source. 15 7/16" x 9 1/2" x 3 1/8"
Light
kit for small trailers. Kit provides all legal lighting and reflectors for
trailers under 80” wide. # 545 kits include one each of 440/440L tail light,
two 114A side marker lights, 25’ trailer harness, 48” trunk connector,
license bracket, mounting hardware
Single or double interior lights, surface mounted with clear acrylic optic lens
Magnetic towing lights two lightweight plastic light heads with magnetic bases, 20 feet of flat wire with a 4-prong flat plug and a 4-hole flat socket
4
7/16” x 1 1/8” acrylic reflector features both adhesive backing and mounting
holes for many narrow applications.
Available in amber or red.
Conspicuity tape 2" wide increases night time visibility 900 candle power and 90 degree reflectivity.